devices_runtime_configuration
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| devices_runtime_configuration [2020/10/04 15:57] – wikiadmin | devices_runtime_configuration [2020/10/04 16:01] (current) – wikiadmin | ||
|---|---|---|---|
| Line 32: | Line 32: | ||
| **Important Parameters for Hosts and Tools** | **Important Parameters for Hosts and Tools** | ||
| + | < | ||
| * deviceId - the device Id. The host and tool must use the same device id | * deviceId - the device Id. The host and tool must use the same device id | ||
| * baudRate - for SECSI tools, this is the serial port baud rate | * baudRate - for SECSI tools, this is the serial port baud rate | ||
| * linkTestInterval - if greater than zero, TransSECS will periodically send an HSMS " | * linkTestInterval - if greater than zero, TransSECS will periodically send an HSMS " | ||
| + | </ | ||
| **Important Parameters for Tools** | **Important Parameters for Tools** | ||
| + | < | ||
| * passivePort - this is the port on which the tool will listen for connections from the host | * passivePort - this is the port on which the tool will listen for connections from the host | ||
| * persistenceFileName - provide a filename for saving the GEM configuration. | * persistenceFileName - provide a filename for saving the GEM configuration. | ||
| + | </ | ||
| **Important Parameters for Hosts** | **Important Parameters for Hosts** | ||
| + | < | ||
| * equipmentHostName - the hostname or IP address of the tool | * equipmentHostName - the hostname or IP address of the tool | ||
| * activePort - the port on which the tool is listening for a connection. | * activePort - the port on which the tool is listening for a connection. | ||
| + | </ | ||
| Line 52: | Line 58: | ||
| Tool application will have these timeout parameters, as defined by the SECS standard. | Tool application will have these timeout parameters, as defined by the SECS standard. | ||
| + | < | ||
| * passiveT1 | * passiveT1 | ||
| * passiveT2 | * passiveT2 | ||
| Line 60: | Line 67: | ||
| * passiveT7 | * passiveT7 | ||
| * passiveT8 | * passiveT8 | ||
| - | + | </ | |
| Host applications will add the following timeouts, again as defined in the standard. | Host applications will add the following timeouts, again as defined in the standard. | ||
| - | | + | |
| + | < | ||
| * activeT1 | * activeT1 | ||
| * activeT2 | * activeT2 | ||
| Line 71: | Line 80: | ||
| * activeT7 | * activeT7 | ||
| * activeT8 | * activeT8 | ||
| - | + | </ | |
| **Uncommon Parameters** | **Uncommon Parameters** | ||
| + | < | ||
| * activeConnectionRetryInterval - for an " | * activeConnectionRetryInterval - for an " | ||
| - | |||
| * passivePort - Host applications. | * passivePort - Host applications. | ||
| + | </ | ||
| **Tech Support Parameters** | **Tech Support Parameters** | ||
| Line 82: | Line 93: | ||
| Change these only if advised to do so by Tech Support. | Change these only if advised to do so by Tech Support. | ||
| + | < | ||
| * allDeviceIdsValid | * allDeviceIdsValid | ||
| * allowDuplicateSECSIMessages | * allowDuplicateSECSIMessages | ||
| + | </ | ||
devices_runtime_configuration.1601841471.txt.gz · Last modified: by wikiadmin